Jump to content



Photo

2000 f 350 sd brake pull problem 7.3


  • Please log in to reply
5 replies to this topic

#1 kevin69bman

 
kevin69bman

    Advanced Member

  • Members
  • 215 posts
  • Location:north east ohio
 

Posted 17 August 2016 - 07:38 PM

This truck pulls real hard to the left when braking hard at all speeds I have replaced the brake hoses, all the calipers ,all the pads and rotors I replaced the master cylinder and the abs unit and it still pulls what the hell have I misted ??? the front end is all new all ball joints,, tie rods, gear box, and pump it drives great down the road till you hit the brake.

 

Kevin


ASE Master Tech

Been doing it to long.

#2 Karrpilot

 
Karrpilot

    STAFF

  • Staff
  • 6,134 posts
  • Gender:Male
  • Location:Chicago Zone
  • Interests:Ex Ford Tech 22 years.
 

Posted 17 August 2016 - 09:01 PM

Just because you replaced that many parts, doesn't mean any of them were any good to begin with. Especially if you have been shopping Auto Drone.

 

An old trick I have found is to now swap the easiest parts from one side to the other. Or to try and split the difference if you can with the front end alignment. Meaning, try and set up the truck to want to go more to the right.

 

See if that helps.


No longer working at dealerships. Government employee. Now i get paid to fix Fords.
ASE master tech
Private Pilot High Performance / Complex Rating.


#3 kevin69bman

 
kevin69bman

    Advanced Member

  • Members
  • 215 posts
  • Location:north east ohio
 

Posted 17 August 2016 - 09:17 PM

No junk auto parts I replaced the front calipers 2 times already no diff

As far as the alignment it drives great the steering wheel will turn to the left when you apply the brakes hard and you can here the left front tire start to lock up on the road along with the rears and leave marks on the pavement before the abs kicks in. The truck drove great for 2 weeks after the gear box was replaced and alignment done

 

I am going to replace the steel brake line next to the right wheel I don't no what else to do it bleeds ok and no hang up it just seems to not be getting the same pressure as the left side

 

Thanks for the info Kevin


ASE Master Tech

Been doing it to long.

#4 fullsizeblazin

 
fullsizeblazin

    Screwed by Car Dealers

  • Members
  • 3,066 posts
  • Gender:Male
  • Interests:Motorcycles, Dirt and street. Spreading the truth about Stealerships
    Since the automotive industry killed my interest in cars,...

    Life is hard. It's even Harder if you're stupid.
 

Posted 17 August 2016 - 10:26 PM

Check the rubber brake hoses for kinks or restrictions.

#5 kevin69bman

 
kevin69bman

    Advanced Member

  • Members
  • 215 posts
  • Location:north east ohio
 

Posted 18 August 2016 - 09:07 PM

Hoses are new the next thing I will do is make up new temp steel lines and put the right side to the left side to the right coming out of the abs unit to see if it moves the pull because the abs unit is used that I installed no new ones available any more.

 

Yes I am at my wits end with this truck :wacko:


ASE Master Tech

Been doing it to long.

#6 fullsizeblazin

 
fullsizeblazin

    Screwed by Car Dealers

  • Members
  • 3,066 posts
  • Gender:Male
  • Interests:Motorcycles, Dirt and street. Spreading the truth about Stealerships
    Since the automotive industry killed my interest in cars,...

    Life is hard. It's even Harder if you're stupid.
 

Posted 19 August 2016 - 10:12 PM

Is this a 4x4?


1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users